金屬軟管的錯誤與正確安裝方法
| 錯誤方法 | 正確方法 | |
|
|
|
說明：180°彎曲安裝，長度過短時，會產 生過度彎曲；應大于最小彎曲半徑安裝。 180 ° bend,radius should belarge than min bend radius to avoid bend excessive. |
|
|
|
說明：不允許小于最小彎曲半徑，應安裝剛 性彎頭。
Avoid impermissible deflection behind the connection fittings by use for rigid pipe bends,observe Min bending radius. |
|
|
|
說明：運動方向與軟管軸線應在同一平面 內，以避免產生扭轉應力。
Direction of movement and hose axis must lie in one plane to avoid torsion stress. |
|
|
|
說明：長度較長時，易出現下垂，此時應安 裝滾筒和托架。
Protect the hose line form sagging behind the fittings by means of a support,A pulley or guiding may be installed. |
|
|
|
說明：避免產生交變應力，安裝剛性彎頭以 消除交變應力和過度彎曲。
Installing rigid pipe bends to avoid torsion stress and bending excessive. |
|
|
|
說明：運動方向與軟管軸線在同一平面內， 以避免產生扭轉應力。
Direction of movement and hose axis must lie in one plane to aviod torsion stress. |
|
|
|
說明：運動方向與軟管軸線應在同一平面 內，以避免產生扭曲損壞。
Direction of movement and hose axis muse lie in one plane to avoid torsion stress. |
|
|
|
說明：自由彎曲安裝時，軟管應避免墻壁、 其他物體和地面磨擦。
Avoid rubbing between hose and wall,ground by appllying appreciate method. |
|
|
|
說明：應安裝滾輪避免過度彎曲。
Avoid excessive bending stress by a pulley. |
|
|
|
說明：即使在普通場合，也安裝剛性彎頭以 避免過度彎曲。
Avoid bengding excessice by application of rigid pipe bend. |
|
|
|
說明：如無法避免外部機械拉伸（如在地面 上頻繁拖動），應外覆保護層。
If there is no possibility of avoiding exterior mechanical strain(such as dragging frequency on the ground),the protection wrap. |
- 上一篇：【視頻】用高速軟管編織機制作金屬軟管 2017/2/10
- 下一篇：2017/1/10